Door Handle Replacement
It's worth it to replace door handles if you don't like the way they appear, or if they're difficult to use. With a bit of patience, you can install the new handle in no time.
Modern door handles are typically equipped with cover plates which hide the screws to give them a more attractive appearance. If your new handle doesn't have screws already connected, you'll need to attach them separately.
Remove the handle that was previously used
Door handles are not only essential for aesthetics of your home, but they're also crucial for safety as they allow you to lock and unlock your door. But, over time your door handle can lose its grip, become loose, or appear old and worn out. This is an indication that it's time to replace it.
If your door handle is becoming difficult to use, it may be time to replace it. This is a problem since it means that you are unable to no longer lock or unlock your door, which could be the risk of security for you and your family.
It is also a good idea to replace the handle on your door when it's damaged or broken. A broken door handle can be extremely dangerous, particularly if your children or elderly family members are unable to open it and end up trapped within. It's simple to fix a damaged handle on doors.
The majority of modern door handles are a standard size and therefore are suitable for any door. If you're not certain that the new door handle you are buying will work, remove the old one and measure the holes in its housing. This will help you to buy the right door handle.
It is easiest to remove the old door handle by removing it from the door. This is typically done with a screw driver. Some door handles come with a cover plate which hides the screws that mount them. You'll need to remove this to get to the screws. After you have removed the old handle, take note of the way the spindle is connected. This will assist you in aligning the new handle.
You can also remove the door handle by depressing the latch mechanism. You can use a screwdriver to remove the door handle. However, you will need to locate the small latch that is located on the edge of the trim piece. After you have removed the latch, take off the handle and the strike plate. Then, you can remove the latch from the door's edge.
Removing the Strike Plate
If you are replacing the handle, you'll need to replace the latch plate that holds the hole that the door's latch hooks into when it closes. The packaging that the new handles come with will offer two options for latch plates - either a rectangular or circular (see the diagram above for the components of a door handle). If your current latch plate has a rectangular shape, switch it to a round one so that the latch is able to hook into the strike plate in a way that makes the handle more comfortable to use.
The first step is to remove the screw that holds the latch plate. These screws are often tight and will require some force to loosen. If you are able, it could be beneficial to have another person assist with this part.
The latch plate should easily come out of the door once the screws have been removed. If it's stuck or won't move then use a small nail file to scrape the edges of the latch plate. This can sometimes free up the plate.
You can now move on to making the new door strike plate for installation. Install the latch plate in the doorjamb using the wood screws that were included with your new handles. Be cautious not to tighten too much the screws, as this can damage the strike plate.
If you're unsure whether the latch plate is in the correct position, close and open the door to determine whether it latches and closes properly. If it doesn't you'll need to adjust the strike plate either up or down, or even forward or back until the door closes and latches correctly.
If the door is still jiggling or moving, you may need to enlarge the hole for the latch in the strike plate. This is more prevalent in older doors, however it can happen due to wear and tear, hinge mortises that are too shallow or not the right size for the latch, or from damage or a broken strike plate that is damaged or broken. If this is the case, follow the exact procedure to adjust the strike plate, but using an iron file instead of a chisel and hammer.
Remove the Latch
The latch is a curved metal piece that slides in and out of a hole in the inside of your door. The latch is pushed forward when you turn the handle. It also catches a hole on the door frame so that the door stays closed. If your door shakes when you close it, replacing the latch could be all you need to correct the issue.
It's difficult to see the screws that secure the latch to the door, however there's usually a small hole on the trim plate that lets you to insert a screwdriver into the slot and pry it off. After you've removed the trim plate, it'll be easy to remove the latch as well as the remaining bolts that hold the latch and spindle in the position.
If the latch doesn't easily be released, try using the clip of a paper or tool to release it from the handle mechanism. Place the item in the recessed latch slot and gently turn or jiggle it until you feel the handle and latch start to split. You may need to repeat this several times before the latch becomes loose enough to let it out.
You should be able to slide the new latch into its slot with no problems after you have removed the old one. Make sure that the latch is correctly positioned in the slot and lined up with the screw chambers, and then use your new screws to fasten it to the strike plate and door frame.
Measure the existing backset (the distance between the centre of the large hole on the door's front and the edge) before installing the new handle. Make sure that the size of the latch of the new handle matches the measurement.
If you're replacing the latch or handle or handle, or if the old lock cylinder is damaged, then you'll require a new one. If you're not changing locks, a new lock should fit inside your existing recess and will work with the keys you have already. Make sure you select a latch with rectangular cover plates that match your old handles.
Take off repairmywindowsanddoors can replace your old door handles with a new lever and rose design to make a difference in the appearance of your house. You can buy complete sets that include matching escutcheons and privacy adaptor kits.
The first step to replace an internal door handle is to remove the cover plate or rose, which hides the screws and inner mechanism. Look for an opening tab on the plate and make use of a flathead screwdriver to pop it off the knob. It may have an opening on one edge or be secured by pins.
Remove the screw that is holding the interior handle and set it aside once the cover plate is removed. Remove the screws that secure both the inner and outer plates. You can loosen them by using the help of a Philips Screwdriver. Take the inner plates and latch from the door. Set them aside.
Most doors have a gap between the door jamb and the edge of the frame that allows for a handle, but not all have. If yours doesn't have a handle, you'll need to make a hole in the door. The process for doing this is similar to the procedure opening a door using locks, but you'll need to take extra care to avoid damaging the door or frame.
The installation of new door knob screws is necessary after the holes have been drilled. Choose the same dimensions as your old screws to avoid getting a handle that is too loose or tight. You'll also have to install a new latch plate and strike rod that aren't included in the majority of door handle sets.
Amazon's Choice FAERSI 2-piece chrome finish handle sets are a great choice if you're in the market of a top-quality interior door handle replacement set. It's a factory fit and has received hundreds of 5-star reviews from happy customers. It's a great choice for replacing worn out or damaged door hardware on your Chevy.